Easter Bunny's Recent Activity
-
Easter Bunny liked jsmith's post in the thread Front sway bar bushing.
When reinstalling anything, its usually best practice to get all bolts threaded and then tighten them down. Are you saying that the...
May 18, 2024 at 7:10 PM -
Easter Bunny liked lasangelos's post in the thread MS6 Treadstone crashbar.
Younger kid driving & he had to be going pretty damn fast. The motor mounts are pushed back a bit You can tell his head hit the inside...
May 18, 2024 at 7:09 PM -
Easter Bunny liked L337TurboZ's post in the thread MS6 Treadstone crashbar.
Part out? I'd be interested in the BNR kit
May 18, 2024 at 7:09 PM -
Easter Bunny liked Raider's post in the thread MS6 Treadstone crashbar.
I have yet to see a factory one be passed through, but I have seen them take the shape of a pole. They absorb energy to keep the motor...
May 18, 2024 at 7:07 PM -
Easter Bunny liked Raider's post in the thread MS6 Treadstone crashbar.
1) Fuck New Age Scammer Nate...if ordering, order from a vendor not banned on so many pages and forums (yes, AFTER he was fired from...
May 18, 2024 at 7:07 PM -
Easter Bunny replied to the thread Brake Booster Vacuum line..
You can use and vacuum line you just need to install an inline check valve so it doesn't get boost to it
May 18, 2024 at 7:06 PM -
Easter Bunny replied to the thread Car sat for a long time. Crank, No Start....
How much gas is in the tank if under half just fill it up with fresh gas and let the car run for a bit. Gasoline is a fantastic solvent...
May 18, 2024 at 12:04 AM -
Easter Bunny liked Mtnbker3531's post in the thread Car sat for a long time. Crank, No Start....
To answer your question about accurate gapping with the coin tool, you don't! The iridium center electrode is brittle and will break...
May 17, 2024 at 8:25 PM -
Easter Bunny replied to the thread Car sat for a long time. Crank, No Start....
It's important to pay attention to how you connect the bare wire before you solder for a strong connection
May 16, 2024 at 6:39 PM -
Easter Bunny liked Raider's post in the thread Adaptive Performance is closed until June 1, 2024.
I also sent an email today reminding him of an outstanding order. June 1, I will determine if I need to remove his vendor placement...
May 16, 2024 at 6:39 PM -
Easter Bunny liked Mtnbker3531's post in the thread Car sat for a long time. Crank, No Start....
As far as underhood wire repair of critical wiring you can never go wrong with a properly soldered connection. Get some high quality...
May 16, 2024 at 1:42 PM -
Easter Bunny liked Raider's post in the thread RaiderFab.com Needs Reviews! Add Yours NOW!.
Yup! Order 2 of these. Raider shared Quik Latch 1.25" QL-25 Mini Latches (SOLD SEPERATELY) with you...
May 16, 2024 at 12:20 AM -
Easter Bunny liked Raider's post in the thread RaiderFab.com Needs Reviews! Add Yours NOW!.
I got you fam. Raider shared 1st Gen Mazda 3/Mazdaspeed 3 Bumper Fitment Solution- FULL KIT with you...
May 16, 2024 at 12:20 AM -
Easter Bunny replied to the thread More Suck, Less Starve.
I didn't think overall had changed much was just curious how important the fill rate on the new basket would be and it seems like not...
May 15, 2024 at 1:15 PM -
Easter Bunny liked phate's post in the thread Ebay Transfer Case.
I've used only CX-7 transfer cases as replacements. They're cheaper and are mostly a direct bolt-in. I wouldn't bother rebuilding an...
May 15, 2024 at 10:23 AM
