Search results

Got my new rear bumper exhaust shrouds on and it looks so much better!!!! I opted for the led lights in them too which wired up pretty easily and I the new look so much!!! It was worth it even if it was $350 or whatever lol

The actual neutral safety switch is a white plug on my speed 6 and is by the clutch arm under the dash a bit. Mine went out and I bypassed it with a paper clip so it would still let me start my car. It also starts in neutral now without the clutch being depressed which is nice. If there is...

So I had a blonde moment apparently and didn't hook up my vac line to the EWG so that explains it not controlling my boost. As for my boost now....... It got neutered lol I am subject to only 10-12 psi now and it is stupid slow lol It sadly feels fast since I have driven a beater pickup for 9...

I purchased a ss clutch line from Edge but I didn't realize it only replaced the very short section of rubber hose. I thought it was going to get rid of the funky swirled circles that go to the slave. I decided not to even mess with it yet but I am not picky about clutch stuff too much and it is...

I always liked where my clutch engaged but when I installed this new clutch it would've been a nightmare without having this adjustment! Glad this info is helpful :)

So lay in the floor board (uncomfortable ik) and look up the clutch arm a good bit and there is a rod with a nut on it that goes through the clutch arm. The LESS threads you show out the front of the arm towards the driver's seat the HIGHER the engagement. The MORE threads showing will lower the...

Have been driving a bit and have around 75 miles on the new setup thus far. Here is a couple mini pulls to just see where I'm at with boost and afr and all that. Running rich and more more boost than I wanted for my first map but this is the 10th rev from my cst4 so it isn't really a tune for...

I will be doing this before too long so thanks JT for the how to. @_Mazdarati did those work even though you're splicing a 3rd wire in instead of only 2 together?

Yes I added a drivers side DM mount. I think the rear diff mount is shot too (which I need to replace soon) which I'm sure will help drivetrain movement and all that too.. I have only driven the car about 50 miles so things are extremely fresh at this point. I might end up trying to get the...

Figured I would give a quick post about the first thoughts of my Clutch Masters CM725 Twin Disc Street series. It is obviously twin disc and has 2 different materials of friction discs but not exactly sure what they're made of. As far as quality it was extremely high quality from what I seen...

So apparently adjusting the MS6 clutch engagement point is stupid easy and amazing! Lol I adjusted it to catch further out and it is in the middle again where it used to be. Such a great thing to have or my experience with this clutch could've gone wayy different! Car is running but seems to...

Got it all bled enough to give it a test drive last night and dang lol The clutch is all at the last inch of the pedal off the floor right now. Hoping I can adjust the pedal for that a good bit as I'm used to it being in the middle more. Needless to say the test drive went good and it is up...

That's awesome man good luck with it!

******** UPDAAATTEEE ******* Oh yess your assumptions are correct... She is alive!!!!!! lol Got it to build fuel pressure through wot gas pedal and cranking it over for 5 seconds or so about 3 times. Then proceeded to fire it up. --- Side note for anyone who has an egr delete --- You can...

First off, I'm jealous how clean your motor is lol Anyway though, secondly, did you double check all the tdc stuff after final tq? I didn't read or missed it on whether you did that. Glad it is coming together for you man! :D

So I have opted for more pie cuts and less couplers lol Hopefully that much welding doesn't bite me somehow but boost leaks should be much less of a problem hopefully! I test fit the bumper over the intercooler and lets just say it is still sticking out the bottom a bit lol I don't want to cut...

Time to try my hand at aluminum apparently lol Water-cooled tig welder be putting in some work lol Played with some settings to get what I liked so tomorrow I will pick up some rod and have a hand at some joints and fit everything up.

After a late night and a bit of work.... The front clip is on and I am getting an idea on how I want my ic piping and fmic. She is looking sexy! Going to buff out my headlights once everything is together as well.

Despite my lack of patience and ability somewhat, I got the job done with my new downpipe. Didn't bother cleaning up the welds so it is as raw as she gets. In my defense I ran out of stainless rod and actually used 1/8" cut pieces of the stainless pipe as my filler which I felt was a decent...