Search results

yes it uses the same bolt holes as the speed 3 subframe, that is IF you are using a CX-7 subframe. Don't have to do really anything with it except move the canister and re-route some hoses. Try checking the fuel filters by the fuel cell before the lift pumps. I had to clean them twice (little...

Well I have been silent for a while now, but unfortunately I sold the car. it'll be located in Toledo area. I just don't really have the time like I did now that I got this new job. I could have just let it sit and sit but someone else is gonna finish what I started sadly, probably for the...

So lets jump back into it sorta, I did figure out the fuel issue. way overlooked but the fuel filters were clogged from the first set of fuel lines I had made. all the little rubber bits inside the hose clogged the screens. pulled them apart and cleaned out with some brake clean, GOOD AS NEW. I...

alright guys, so I took the car out last weekend and it was ripping, no hiccups or anything. I come back this weekend to get yall a video and well you can see for yourselves. it seems fuel psi is dropping mid pull (400-700 psi). my guess is that the fuel psi regulator is just not enough to...

Let me know what you guys think about this log. long story short, at WOT (doesn't matter what gear) around 4k rpms it just goes WAHHHH-pop-pop-pop-pop and doesn't accelerate anymore. kinda like some rolling antilag minus the GO or 2-step sorta thing. I looked at the log and the accelerator pedal...

Man.... I feel like this is the never ending project, But progress is always being made here. so it took nearly a month to receive my axle seal from the dealer, what a joke. while I was waiting I have been busy tending to the issues I've been having with the car, like cooling, and the boost...

So its been a while, I took a break for a minute. I have been just non stop working on the car every weekend. But GOOD news, I have been putting miles on the car and other than "random" coolant temps and what seems to be a "non-existent" axle seal its doing good. I still have a wobbly rear end...

I have some leftovers of this fuel hose and some fittings and was wondering if anyone would want to run one of these? it replaces the factory fuel inlet hose with the blue clips that always breaks (from low pressure steel fuel tube on firewall to HPFP inlet). I have enough material to make...

There is room where its not needed and no room where its needed if that makes sense. the lowest point is the 2 bolt flange. I may just have to cut that out and put a piece of flex or straight pipe there instead, which will give me another inch but hey anything at this point helps.

So the last thing I needed to get done before I start road testing this is to make a full exhaust, so this past weekend I spent doing just that. now I'm gonna have ground clearance issues but its either be really loud or have some ground clearance issues. I may have to buy some stock speed 3...

Hey guys, some more progress is being made. So lets start with the misfire issue, I have gotten 1 of my sets of injectors cleaned and ordered some Corksport seals. I then decided that its never a bad idea to clean the valves when the intakes off so I spent a couple hours cleaning them, lets...

Honestly I have been running those coils since I got the car. it was the first thing I bought along with spark plugs and basic maintenance parts when you buy a new car. I never had an issues with them. but I have many spare parts on my shelves so I just grabbed a set of oem ones from an old...

I forgot to dump some photos of the wiring mess I made in and out of the engine bay this past weekend. also getting finished up with the fuel cell area. I plan to keep the back seats in place as I'm not planning on building a firewall, although id assume to even go on any track with it id have...

alright excuse the noob question, But what time does this start or is it like an all day thing? ill be down there Thursday night. Just wanna make sure I dont miss anything. I have never been so its all new to me. :sweatsmile:

@JohnnyTightlips I have all my logs from that run I did.

alright guys LONG STORY I have a misfire issue that I'm just gonna assume is related to my injectors and or seals. so lets go back to the first video of me driving the car down the road. after reviewing the logs it seems I hooked up my ebcs wrong and had 0 WGDC and made around 31psi. so after I...

Damn if only my car was done. maybe ill just bring the fiesta out for some fun, its only a 9 hour drive from me so what the hell why not??

So the reason I didn't take those pics is because it uses the factory holes from the speed 3, no modifications needed there. The motor mount is rather an experiment, if the vibes are too much ill explore other ideas i have. maybe get bigger ends to accept bigger bushings. this was simply to see...

Alright I forgot to tell you guys something. remember the "custom axle" I needed because the speed 3 axle will not work at all, you have to use a speed 6 axle to go into the transfer case. Well I actually got a oem speed 6 axle (front passenger side) to work with no issues. after a bit of...

Well you got me there, I did not get it professionally done no. I just aligned it as good as I could my self, but now that you mention it I totally forgot the camber arms, WHICH could be the main issue, if one wheel has more/less camber than the other it will cause some issues. luckily these...