Search results

  1. L337TurboZ

    I like Doritos

    Since there's literally no posts in this section then I'll be the first to say I like Dorito engines. A weird combination of two stroke, 4 cycle, and airplane technology. Maybe I'll find an RX8 or a Mazda B series truck to start a rotary build on.
  2. L337TurboZ

    New section requests?

    Why not move the vendors section down the list and bump up the MS3/MS6 sections to the top?;
  3. L337TurboZ

    Building for the road course...again

    All that extra work for 1 horse torque lol. Good luck with it. Are you going to get any seat time this season?
  4. L337TurboZ

    Another No start

    Start a new thread with a list of mods and other recent repairs. Chances are you probably blew something up if it just cut off like that.
  5. L337TurboZ

    Building for the road course...again

    Did you scuff the surface with sandpaper before applying it?
  6. L337TurboZ

    Effects of high eth content on fuel level sensor

    I've said it before but I'll say it again. Someone should hook up a 3 wire potentiometer inline with the signal wire for the sender. Then measure the resistance of the circuit to determine what ohm resistor could be wired in. All it would take is adjusting the dial until the car reads full or...
  7. L337TurboZ

    Driver Side Transmission Axle Seal Installation Questions

    I meant use a tube with those bearing/race installer tool. I have a ball joint installation kit which has tubes and cups. I use the bearing and race tool with the cup to hit those seals in. Or you could go to an exhaust shop and see if they'll let you get a spare 1-2' piece of exhaust that's...
  8. L337TurboZ

    Driver Side Transmission Axle Seal Installation Questions

    That's crazy. I've put in a ton of output seals and have never run into an issue like that unless you're using something the wrong way. Try something like this https://a.co/d/hLksCuC
  9. L337TurboZ

    Endgame setup- BW s257sxe

    If the kid wants to watch Bluey then they'll do what they're told. No TV time until the car runs.
  10. L337TurboZ

    Building for the road course...again

    Looks like mint
  11. L337TurboZ

    Need Advice on Tuning VVT Table for Faster Turbo Spool.

    Have you adjusted WGDC at the same time as VVT adjustments? Have you changed any boost target levels?
  12. L337TurboZ

    Building for the road course...again

    Lol you can buy adapters
  13. L337TurboZ

    Building for the road course...again

    This might come in handy or you can make your own Melling Pre-Lube Engine Oiler Tool https://a.co/d/1H0xuT2
  14. L337TurboZ

    Can't do this cranking, no start, no codes, no rail pressure issues much longer.......

    Is the plunger/roller there for the HPFP? If it isn't then nothing is going to be hitting the valve to generate pressure in the HPFP. It's a mechanical pump with an electric controlled release valve.
  15. L337TurboZ

    Building for the road course...again

    I'm still following this. I like seeing the progress you've made. I used to do the same thing you're doing with building an engine or transmission inside the house. It was chill. Smoke a bowl, watch tv, and just wrench while doing it. Had my PC hooked up to my TV as a monitor so I could easily...
  16. L337TurboZ

    [SOLVED] MS6 PCM Not sending ground to OCVOCV

    It sounds like you have a short between the wires or a short to voltage. You should check continuity between the OCV and the ECM wires and then load test each wire to make sure there isn't high resistance somewhere. Remember that one strand of wire can be good and show low resistance which is...
  17. L337TurboZ

    [SOLVED] WasteGate Duty Cycle not effecting boost

    Is the turbo IWG or EWG? Have you checked for cracks in the turbine housing near the WG swing valve where it seals to the housing if it's IWG? There could be other limiting factors such as tune etc. If you're trying to do target torque VS target boost it might limit boost because you're hitting...
  18. L337TurboZ

    Reverse light not working, Mazda 3 2010 1.6 Manual

    All voltage in a circuit should equal zero when a load is applied. IE if you did a voltage drop test with a bulb illuminated testing between the + and - side of the bulb there would be 0 volts registering. If you had any voltage then there is excessive resistance either in the circuit or the...
  19. L337TurboZ

    [SOLVED] New Eonon M3BKA12 no audio on 07 Mazdaspeed 3 with Bose

    I'm pretty sure I made a post a while ago that has a list of codes for the head units to unlock more options
  20. L337TurboZ

    [SOLVED] New Eonon M3BKA12 no audio on 07 Mazdaspeed 3 with Bose

    On my old unit I had to move connections around as there were extra plugs for the Bose or non Bose options. Maybe yours is similar?
Back
Top