Search results

Behaves normally. Fluctuates with low numbers or at 0.

+20 and it goes to zero on throttle. When it does the flashy CEL during limp mode, it goes to zero.

So couldn't mess with the car for awhile because of life but now life necessitates getting this thing sold. I rebuilt my boost leak tester and got it to hold boost. All of the lean engine codes are gone. The car is now throwing 0301 which is misfire on cylinder 1. When it goes into limp...

Pulled the plugs and they vwere badly fouled despite being changed somewhat recently. Going to replace them tomorrow and hope that gets everything situated.

Did the boost leak test. Can't keep the pvc sealed perfectly on the intake but it holds pressure until it breaks the seal there. Filled it up with smoke prior to running boost leak and can't really see any leaks. No more lean code as pending but cylinder 1 misfire is still showing up. Idle is...

Yea, cleared with the scan tool and then let off the battery cable.

Well, almost completely back to normal. Replacement solenoid put in and new clamps on all the lines on it. No more leaks visible with smoke. Still need to run the boost leak test again. The car will still go into safe mode but wat less frequently and will resolve itself early. Only pending...

So after messing with vehicle selection for quite some time on dorman's, carpoarts, and dealer sites, the 2013 model year does not register any parts/part numbers for it. Changing it to a 2010, you get the Dorman 911-909 as the match. Weird, annoying quirk. I quickly hit your link and assumed...

When you put in the Speed as the vehicle, it says that one doesn't fit. The Speed also isn't on the listed vehicles for fitment for it.

If I was going to keep it, that would be an option but trying to get it running right to sell it.

Google image search is amazing LF82-18-741 Intake manifold runner solenoid. Autozone has a part that comes up when I search the number but it says it's not compatible with the vehicle. Anyone know if that will work?

Smoke machine arrived early. The black evap thing under the intercooler was leaking tons of smoke. Dumb question. But what is the name of this part? Haven't done the boost leak test again yet.

I will do it again tomorrow or Sunday and let you know. Also, I really appreciate the help everyone has offered in this.

Did a boost leak test. Didn't think to check the oil fill cap when I did it. It's how I found the busted hose clamp. And tried some Ace Hardware orings and they are just barely off the original ones. If anyone knows the right sizes (don't have anything to measure the original ones properly)...

This damn car is infuriating. New brake booster line is installed and made an improvement but still the same issue. Stability control light went off. Have gone over intake chain mutliple times and can't find any leaks. Had a buddy just look with me for a second set of eyes and same thing...

So wasn't the intercooler. One of the throttle body hose clamps was busted but didn't look busted. Replaced it and was still getting the same issue with but slightly less worse. Stability control light came on so decided to thoroughly go over the brake booster line and it has a leak in the...

New harness is installed and made a huge difference. Still throwing a pending lean code. Took a short drive and it ran great until safe mode which took much longer to trigger and went away faster. Did a boost leak test and no obvious leaks but I think my intercooler may have a slight leak on...

Not the best with wiring but I pulled two pins and the wire that I thought is the issue is definitely a problem (may not be the final solution but definitely needs attention). Ordered a pig tail from Amazon. Easier for me to solder it in vs. fighting with the pins. And for anyone else that...

Had a buddy come by for a second set of eyes/ears and while he was here I double checked the MAF harness. It finally did affect it when moving the wires around. It's now throwing the two MAF codes. It looks like it is the middle wire. Can I pull the wires and rewire it or should I just buy...

Well have to build a tester so will probably be a couple days before I can test it.