Recent content by NinjaCustoms

New Update - Calculations on Brake System I tuned my brake setup as described much earlier - new stronger Brembo M85 054 brake pump thet fits perfectly - only needed to machine adapter. Brembo 18Z 6 pot Calipers on front and 2x 4pot on rear - one pair as normal brake and other as hydraulic...

,,New Year,, Fix - Update I managed to fully inspect damage, small issues I fixed on spot but those unfixable as plastic trims i dismantled and took home for repairs. Whole Xenon trim (without lamp, including only trim) needed to ordered , i need car soon and i will fix it with ease later...

I'll do my best and it will be as OEM, trust the skill The OEM bumper won't be needed strictly anymore but why I'll announce here after I'll be sure one step of my secret project will succeed

New Year Update It started ,,fabulous,, New Racing Sparco gloves Snowy weather aaaand? And a tree Couldn't imagine ,,better new year,, Now my bodywork skills have finally been challanged. I only need to order new/used in good shaped trim, swap halogen unit (restore black out mod) , weld...

NEW QUICK UPDATE - ADDON TO CERAMIC COATING That's how a nice seal from rtv should be done on the shark fin antenna, not as i did as a noob earlier. I personally think that it can't be than better and my skills in tuning/detailing are growing quick while doing this project

PROJECT MAIN UPDATE I can proudly announce i started to create custom Pandem bodykit for my CX in drag racing style because it ll be a drag build. Phase I included prototype sketches - done Phase II corrections to sketches, aerodynamic simulations and various tests to achieve perfection...

NEW UPDATE - DETAILING, PAINT - PART II - LAST IT'S last part of detailing my mazda because i realized it's a waste of time . Not in a bad way but trying to make 15yr old car look brand new in some states is not reasonable. I realized the trueness of the phrase ,,old cars don't try to hide...

NEW UPDATE - DETAILING PART I- GLASS I decided ti give car a good clean , it was not in bad condition but paint is slightly scratched and all glass surfaces are strangly matted (maybe from paint dust from painting the bottom). This dust is hard to remove but there are two ways . Use special...

NEW UPDATE - 1 YEAR ANNIVERSARY OF THE BUILD As one year passed since first seriously mods rather than putting some stickers (which were removed later in my Anti-Lame mod) On the video below we can see how different the car became so far, better engine sound (intake) better interior (alcantara...

RPM SHIT LIGHT AND ALTERNATOR SENSOR FINAL UPDATE finally my shift light works and it's set to 4k rpm . I'll be quick, few corrections needed to be done. First this sensor does not accept hot wire 12v, it needs to be the ignition on 12v that only works after turning key in acc position. I...

RPM SIGNAL / SHIFT LIGHT UPDATE I did this rpm adapter the better way as promised - no zip ties were used to attach sensor. Let's start with preparation step. Remove engine cover and locate alternator - either driver or passenger side- usually on the left. Look for the best position for the...

MAINTENANCE UPDATE - HOW TO CLEAN YOUR OIL CATCH CAN/TANK Firstly remove the hoses itself and whole can from the chassis however you installed it- mine is screwed on the left side Then look if your can is empty - look at the transparent hose Mine after a year or sth was pretty full of oil...

LAST ALCANTARA UPDATE (I THINK) I just finished and installed the gauge panel above the steering wheel. The bending wast hard to straighten but i found a way. As always quick shot and stay tuned

NEW RPM SHIFT LIGHT UPDATE I found best solution for non working rpm shift light that may save any build. Mainly those drag racing look shift light rely on simple pulse signal generated by a car computer or by a sensor detecting movement with calculated ratio of spins per some time that gives...

NEW INTERIOR MOD UPDATE Finally done . Sunvisor are good but not as perfect as i wanted them to be bot here you have, full suede.