What did you do to your ride today
- Thread starter CmdrShepard
- Start date
- Watchers 119
Sleepy_Pat
Greenie N00B Member
Hell yeah, much appreciated
ibcrusn
Greenie N00B Member
Finally started the arduous process of hand washing and full detailing of the paint before winter hit with salt and all the other crap on the road. Also swapped the OE TMIC back to ETS and flashed ECU now that autocross is done for the season. Now that it's cooler I should get busy and work on both tunes so the car runs spot on come spring.
Darthxar
Greenie N00B Member
I really need to do the detail prior to winter thing as well. Also changed oil today and looking at my records realized my plugs are 17k miles old, so those have got to go. Soon it will be time to Jack up the suspension and put the snows on
Sent from my XT1575 using Tapatalk
brainbot1
Greenie N00B Member
Did the GM cylinder cleaning over the weekend in hopes of regaining some compression, no luck, cylinders 2 and 3 are still diminished 
Engine rebuild in my future oh well.
Replaced front brake pads to Hawk HPS.
All with the help of @VTMongoose !!! I'm a newb and john knows all
Engine rebuild in my future oh well. Replaced front brake pads to Hawk HPS.
All with the help of @VTMongoose !!! I'm a newb and john knows all
God dammit, I need this now.
I did this today, too bad it will just be pointing my mushy snow tires around for the next three months.
Sent from my XT1575 using Tapatalk
crapatalk, yes it sucks for free.
CorkSport - Derrick
Approved Vendor
Picked up one of these and the drop floor for the Spec Miata.
ToyCop
Greenie N00B Member
Got all of the wiring and tubing squared away on my boost gauge. I went with larger tubing from the BPV line to the boost sensor than what was provided with the gauge. Since the clamps wouldn't be tight enough to hold I slid a portion of the clear tubing onto both ends of the filter and the sending unit. I then cut the clear tubing flush with the opening. The new silicone slipped over pretty tight and the clamps are holding great now. I drilled a hole in the side of my battery box and inserted a small rubber grommet that allows the sending unit to rotate if i need to unplug it for box removal. I used a shortened screw and nut from a computer case fan to tie it all together. I still need to run the illumination wire so the gauge will change color when the lights are on. When my oil sandwich plate gets here I'll hook up the oil pressure gauge.
iguardflorida
Greenie N00B Member
took pictures of the dip job I just finished on it!
Last edited:
Picked my car up from the shop today.
Anyone else experience the front LCA bolt rusting/seizing to the steel sleeve inside the inner-front bushing? I got to deal with that fun little adventure (or so I thought?*) while trying to install a CS lower tie bar; eventually had to take it in because I just don't have the proper tools, space or experience to deal with that shit. Most expensive $120 mod I've ever done.
*The shop tells me that the bigger/actual problem was that the nut that's hard-welded to the subframe at the backside of the bushing (where the bolt threads into) had apparently broken free and was just spinning. They had to do a c-section to re-weld the nut and then button everything back up.
Anyone else experience the front LCA bolt rusting/seizing to the steel sleeve inside the inner-front bushing? I got to deal with that fun little adventure (or so I thought?*) while trying to install a CS lower tie bar; eventually had to take it in because I just don't have the proper tools, space or experience to deal with that shit. Most expensive $120 mod I've ever done.
*The shop tells me that the bigger/actual problem was that the nut that's hard-welded to the subframe at the backside of the bushing (where the bolt threads into) had apparently broken free and was just spinning. They had to do a c-section to re-weld the nut and then button everything back up.
Whilst giving myself another headache reattaching my CP-E downpipe to my turbo for the 3 millionth time, it occurred to me that I should make a PSA for people thinking about buying one of these.
Sent from my A0001 using Tapatalk
Last edited:
Darthxar
Greenie N00B Member
Well I guess CPE is of my list then. I've been debating which down pipe to get.
Sent from my XT1575 using Tapatalk
Cocksport worked well for me. Plus the sound is awesome. I have a catted pipe.
crapatalk, yes it sucks for free.
Maisonvi
Grass-Roots Vendor
Ebay. Had mine for years with no issues. Cost like $120 shippped.
